Types of Concrete Anchors: Screw, Sleeve, Wedge, Drop-In and Chemical

Compare concrete screw, sleeve, wedge, drop-in and chemical anchor types, including base materials, setting methods, removal and purchasing requirements.

The main types of concrete anchors are concrete screws, sleeve anchors, wedge anchors, drop-in anchors and chemical anchors. For buyers, the useful distinction is how each anchor transfers load into the base material, what installation equipment it needs and which parts you can remove later.

This guide compares the five types of concrete anchors before you move to a product specification. It helps distributors and project buyers describe the required anchor clearly, separate concrete from masonry applications and identify missing information in an enquiry. Start with the substrate and connection detail, then select the anchor system.

[IMAGE 1: illustration of five concrete anchor types side by side, labelled as illustration]

Types of Concrete Anchors at a Glance

Type and principleBase material to checkWhen loading can beginRemovalTypical use
Concrete screw: thread engages the drilled holeConcrete; masonry only where specifiedAfter correct installation and required acceptance checksYou can generally remove the screw; reuse needs separate confirmationFrames, brackets and fixtures
Sleeve anchor: sleeve expands around the studConcrete, solid brick or dense block, subject to the product dataAfter correct setting and required acceptance checksFixture removal depends on design; anchor parts may remainGeneral fixtures and brackets
Wedge anchor: clip expands against the holeSolid concrete as specifiedAfter correct tightening and required acceptance checksYou can remove the nut and fixture; the embedded stud generally remainsBase plates and steelwork connections
Drop-in anchor: internal plug expands the anchor bodySolid concrete as specifiedAfter correct setting and required acceptance checksYou can remove the bolt or rod; the anchor body remainsThreaded rod and service supports
Chemical anchor: resin bonds the rod to the substrateConcrete or masonry covered by the selected resin systemAfter the specified curing conditions are metYou can remove the fixture; the bonded rod generally remainsDesigned stud connections and specified masonry fixings

These are type-level differences. Design values, base-material suitability and installation data should come from the anchor’s technical data and the project engineer.

How Concrete Anchors Hold: Mechanical vs Chemical

Mechanical anchors transfer force through contact between steel and the surrounding substrate. Expansion anchors use a cone, wedge or plug to press an expansion element against the drilled hole. Concrete screws engage the hole through their thread form. These mechanisms explain why the hole and setting method are part of the anchor specification.

Chemical anchors use a resin bond between the rod and the substrate. The stud and resin form a system: choosing the steel rod alone does not establish the joint’s performance. Resin selection, hole preparation and curing conditions all affect whether that system carries its load as intended.

In contrast, mechanical anchors do not need resin to cure. They still need correct installation before loading. Chemical anchors add a curing stage, which you must consider when planning installation access and the sequence of work.

[IMAGE 2: illustration of mechanical expansion, screw engagement and chemical bonding, labelled as illustration]

Concrete Screws (Masonry Screws)

Concrete screws engage the surrounding material through a purpose-designed thread driven into a prepared hole. They do not use a separate expansion sleeve. The screw’s geometry, drilling requirement and intended substrate must match; a familiar head shape does not establish that two products are interchangeable.

For example, a practical advantage is removal. You can generally unscrew the screw when a fixture needs to move or be replaced. Removing a screw does not automatically make the screw or the existing hole suitable for reuse. Treat reuse as a separate requirement when discussing temporary or serviceable connections.

Head style affects how the fixture sits and how the installer reaches it. A countersunk concrete screw suits a compatible countersunk fixture; a slotted concrete screw offers a different drive arrangement. Review concrete frame screws for frame fixing enquiries and masonry bolts and screw bolts for that product family.

Specify the fixture thickness and access available for driving. Leave embedment and hole requirements tied to the selected product rather than copying them from another concrete screw.

Sleeve Anchors

A sleeve anchor has an expansion sleeve around its stud or bolt. Tightening draws the cone into the sleeve and expands it against the hole. This gives it a different expansion arrangement from a wedge anchor, whose clip sits near the end of the stud.

Buyers commonly consider sleeve anchors for fixtures in concrete, solid brick and dense masonry block where the chosen product supports that application. In contrast, solid masonry and hollow masonry need separate consideration. The presence of a sleeve does not make an anchor suitable for every type of block or for a damaged joint.

Different head and nut arrangements suit different fixtures. When enquiring about sleeve anchors, identify the fixture’s hole, seating surface and whether a projecting stud is acceptable. If later removal matters, describe what must be removable: the fixture, the fixing head or the whole embedded anchor.

Wedge Anchors (Through Bolts)

Wedge anchors use a cone and expansion clip near the embedded end of a threaded stud. Tightening the nut activates the expansion arrangement. Installers generally use them for fixings into solid concrete, including designed connections for steel fixtures and base plates.

In fact, the name “through bolt” can describe installation through a fixture; it does not mean the anchor needs a nut on the far side of the wall. Check the specific product detail rather than relying on the name alone. Once installed, the embedded stud normally remains when you remove the nut and fixture.

For a wedge anchor or through bolt enquiry, describe the concrete, fixture thickness and exposure. Material descriptions may distinguish the stud from the expansion sleeve. A corrosion-resistant component in one position does not define the material of the entire anchor assembly.

Drop-In Anchors

A drop-in anchor has an internal thread, and installers generally set it flush with the concrete surface. A setting tool drives an internal plug to expand the anchor body. You then attach a compatible bolt or threaded rod to the installed anchor.

This form is useful where you do not want a projecting stud before the fixture is fitted, or where you may need to remove a rod or bolt later. For example, service supports and suspended threaded-rod connections are common examples, subject to the particular anchor’s intended use. The embedded body stays in place when you remove the bolt.

Setting equipment is part of the purchasing discussion. Linkworld’s drop-in anchors page states that setting tools do not come with the anchors. Confirm the tool requirement, matching thread and rod or bolt supply separately, rather than assuming that a carton of anchor bodies is a complete installation kit.

Chemical Anchors

Chemical anchors bond a steel stud or rod into a prepared hole using resin. Consider them where a designed bonded connection suits the substrate and joint. They can also be relevant to engineered details near edges, but a chemical system does not remove edge-distance or spacing requirements.

However, in hollow masonry, a compatible resin system may use a mesh sleeve to retain the resin within the required zone. Specify the masonry, sleeve, resin and rod together. Do not substitute a concrete installation detail for a hollow-block connection simply because both use threaded studs.

As a result, loading must wait until the resin has cured under the stated installation conditions. Temperature, substrate condition and the selected system matter, so a general curing time is not a useful purchasing specification.

Linkworld’s chemical stud anchors are the steel stud components, supplied with nuts and washers; the supply does not include resin. Identify the compatible resin system and any required sleeves separately when assembling the order.

How to Choose Types of Concrete Anchors: Base Material, Load Direction, Edge Distance and Environment

Work through the connection requirements before choosing a product code. Buyers can collect these details without trying to replace the anchor design.

  1. Identify the base material. State concrete, solid brick, dense block or hollow block. Include the available project information about its condition. Avoid describing every substrate as “masonry” when the anchor choice depends on what is inside the drilled hole.
  2. Describe the load and fixture. State whether the connection is mainly in tension, shear or a combination, and identify vibration or repeated movement where relevant. Supply the fixture drawing, thickness and number of fixing positions.
  3. Show the available geometry. Mark edges, neighbouring anchors and restrictions behind the fixture. A drawing lets the designer assess whether the required spacing and embedment are achievable without guessing from a photograph.
  4. State the exposure. Identify indoor, outdoor, coastal or other corrosive conditions, including the materials touching the anchor. Compare electro-zinc, hot-dip galvanised and stainless options against the project specification; see fasteners for outdoor coastal projects and stainless versus coated steel.
  5. Plan installation and later access. Confirm drilling and setting equipment, access for tightening, any curing stage and what you may need to remove for maintenance. These requirements can distinguish otherwise similar anchor enquiries.

What to Send When You Order Concrete Anchors

A useful order list identifies the anchor type and the product reference, then separates the steel component specification from its installation requirements. Include:

  • Anchor type, head or internal-thread form, and required dimensions
  • Fixture thickness and the approved embedment or installation detail
  • Material and finish for the relevant assembly components
  • Base material and the intended application
  • Quantity by item, with nuts, washers, rods, resin, sleeves or tools identified separately where required
  • Bulk or own-brand packing, item labels and destination
  • The drawing revision or representative sample for a custom requirement

See the product page for available sizes; we can make other sizes and finishes to drawing or sample. Custom geometry still needs to match the technical requirements of the intended anchor system.

Linkworld supplies standard and custom fasteners to business buyers, with 18 years of fastener export experience and its own inspection room and QC team, checking before every shipment. We can make parts to your drawing or sample and provide bulk cartons or your own-brand boxes, tubs and small packs.

Frequently Asked Questions

What are the main types of concrete anchors?

The main types of concrete anchors are concrete screws, sleeve anchors, wedge anchors, drop-in anchors and chemical anchors. Screws engage the hole with their threads. Sleeve, wedge and drop-in anchors use mechanical expansion. Chemical anchors bond a rod into the substrate with resin and require the specified curing conditions before loading.

Which concrete anchor is best for brick or hollow block?

For solid brick or dense block, a sleeve anchor may be an option where its product data supports that substrate. Hollow block may require a compatible chemical system and mesh sleeve. Identify the masonry first, then select a system intended for it; do not assume that a concrete anchor suits every block.

Wedge anchor vs sleeve anchor: what is the difference?

A wedge anchor expands a clip near the embedded end of its stud and installers generally use it in specified solid-concrete applications. A sleeve anchor expands a sleeve around the stud and may cover suitable solid-masonry applications as well. Finally, the product data and connection design determine which is appropriate.

Can concrete anchors be removed and reused?

In short, removal depends on the anchor type and on which component you mean. You can generally unscrew a concrete screw, while expansion bodies or bonded rods usually remain embedded. A removable fixture does not imply a reusable anchor. Confirm any reuse requirement for the specific product and existing hole.

Do chemical anchors include the resin?

Supply scope varies, so check the product listing. Linkworld’s chemical stud anchors are steel studs with nuts and washers; the supply does not include resin. Specify the resin system and any required sleeves separately. Confirming these components at enquiry stage avoids treating a stud-only order as a complete bonded-anchor installation kit.

Browse the concrete fasteners range, then send your list, drawing or sample with the base material, application and packing requirements for review.

Send an Enquiry

Send a drawing, sample or clear reference photo. Add the quantity and application if available, and we can start from the information you already have.